You are reading the article Windows Is Stuck On Repairing Disk Errors, This Might Take An Hour To Complete updated in December 2023 on the website Cattuongwedding.com. We hope that the information we have shared is helpful to you. If you find the content interesting and meaningful, please share it with your friends and continue to follow and support us for the latest updates. Suggested January 2024 Windows Is Stuck On Repairing Disk Errors, This Might Take An Hour To Complete
Some Windows users report an issue in which their computer gets stuck at Repairing disk errors, This might take an hour to complete screen. It usually occurs due to Hard Disk issues. Disk errors can occur for a number of reasons, but they generally happen due to a physical failure, such as a scratched disc or bad sectors on the disk. Recently some users reported experiencing an error message when they start their Windows.
Repairing disk errors, This might take an hour to complete What is Repairing disk errors this might take an hour?Disk errors are a common experience on your hard drive. They’re usually not critical, and they can be fixed in just a few minutes. But sometimes you might need to fix disk errors that take a long time. This is because there’s another problem with your hard drive or the computer’s configuration. But before you go out and buy a new hard drive, let this article show you how to repair disk errors that take an hour.
Windows is stuck on Repairing disk errorsThis error occurs because of a potentially failing HDD/SDD. We will be seeing all the solutions to fix the error.
Wait for a few hours and see
Remove all external devices
Restart in Safe Mode and use CMD to run chkdsk
Run Repair-volume command
Use System Restore
Run Automatic Startup Repair
Repair computer using Installation Media
Check and replace your Hard Disk
Let us talk about them in detail.
To carry out some of these operations, you need to boot into Safe Mode or to the Advanced Startup Options screen.
1] Wait for a few hours and seeYou need to first wait for a few hours or overnight as sometimes, the computer will automatically rectify the error. This is somewhat obvious if you read the error message appearing on your screen. So, wait for some time before moving to the next solution.
2] Remove all external devicesThere is a possibility that Windows could detect the external drive as the system boot partition, causing your PC to crash upon booting. To avoid this problem, you first need to disconnect all external drives attached to your computer and then restart your computer. Now check if your PC can boot normally after it starts. If this works, reconnect all your external devices one by one and check which one is causing the problem. When you find the faulty device, replace that with a new one.
Related: How to stop or cancel ChkDsk in Windows.
3] Restart in Safe Mode and use CMD to run chkdskRun CHKDSK to repair bad sectors of the Hard Drive. If you know that there are bad sectors in your Hard Drive, try using the CHKDSK command of Command Prompt to rectify the issue.
We know that your computer is not booting, therefore, we have given the following steps to run the command.
Now, select Safe Mode.
Open Command Prompt and execute the following command.
chkdsk
/f C:This will run the command for the “C” or System drive.
Related: ChkDsk stuck at a particular % or hangs at some Stage.
4] Run Repair-volume commandYou could run the repair-volume command using Windows PowerShell and see if it helps. These are steps you can use to accomplish this:
Before you go to the steps, note down the drive letter of your external drive.
Open the elevated Windows PowerShell window on your computer
Type the following command and press Enter:-
Repair-Volume drive-letter –ScanPlease replace “drive-letter” with your original drive letter in the command line above
Now run the following commands:
Repair-Volume drive-letter –OfflineScanAndFix Repair-Volume drive-letter –SpotFix
Once you complete the steps, wait until the scanning process is complete. Restart your computer when it’s finished.
Related: Scanning and repairing drive stuck in Windows
5] Use System RestoreIf you have created a System Restore point, try using it to fix the issue. You can use the following steps to do that.
Finally, perform the System Restore and see if the issue is resolved.
6] Run Automatic Startup RepairIf you don’t have a System Restore point, you can run Automatic Startup Repair. To do that, you have to first force Shutdown your computer and then when it starts again, press the power button to shut it down. Do this for 2-3 iterations and you will see the “Preparing Automatic Repair” screen.
If Automatic Repair is capable of fixing the issue, it will automatically do that you rectify the issue for you.
7] Repair OS using Installation MediaIf nothing works, you need to do is repair your computer using Installation Media.
This won’t delete your files, so, you can do that without any worry.
8] Check and replace your Hard DiskIf repairing didn’t work, try checking your Hard Disk, and see if it has malfunctioned. Unfortunately, if your hard disk is irreparable, you have to get a new one.
You can use WMIC to check Hard Disk Health. But since your computer is not booting, you have to plug your Hard Disk into a different system and check its health.
Related: The disk does not have enough space to replace bad clusters
How long does Repairing disk errors take in Windows 10?It normally takes 10-15 minutes depending on the Disk size and state. But as you can see in the error message itself that it may take an hour to finish – but sometimes, you have to wait for a day before starting the troubleshooting process. So, do that and check if the issue persists. If it does not get fixed automatically, you can refer to the aforementioned solutions.
How do I fix the Hard Disk error?If you are sure that Hard Disk has malfunctioned, there is always a way to fix the issue. There is a command that you can run to rectify the issue. You need to run the CHKDSK command (aforementioned) to fix the Hard Disk error on your computer.
Read: Bad sectors were encountered during the format
What causes Repairing disk errors?The most common cause for repairs is system file corruption or registry error. When these files are corrupted, Windows is unable to run, which causes the error message to pop up. And since Windows is mostly reliant on system files, it’s pretty easy for it to malfunction when they get corrupted. Some other common causes include malware infection, stuck keys in keyboard or mouse, hard drive failure.
Related:
You're reading Windows Is Stuck On Repairing Disk Errors, This Might Take An Hour To Complete
Fix: “Repairing Disk Errors This Might Take An Hour”
Sometimes while Windows initiates, you might encounter the “repairing disk errors this might take an hour” message on the boot screen. This error generally occurs when there are issues on your hard disk and Windows tries to troubleshoot disk problems during the boot process.
Many minor issues are automatically fixed by Windows but it might take time. But in most cases, the issue can be more critical and won’t be solved even after leaving your computer alone for hours or even days. So, if you’re in a situation similar situation, this guide is just for you.
What Causes the “repairing disk errors this might take an hour” Error?In the simplest scenario, this error may occur due to a forced shutdown. It can be caused by either sudden power cuts or accidental pressing of the power button. But other reasons that cause this error message to occur are:
Corrupted Peripheral Devices.
Issue within Windows files.
Bad sectors in disk
Hard disk failure
How to Fix the “repairing disk errors this might take an hour” Error?You must reach the Windows Advanced Startup options screen first to try the solutions within this article. Turn off your computer by holding the power button for 10 seconds. Then turn on your computer and repeat this process for three times. On the third restart, you should enter the Windows Recovery Environment.
Then you are set to try out the solutions below:
Startup RepairStartup Repair is also another inbuilt tool of Windows to troubleshoot errors preventing it to start up. Open the Advanced Startup Option screen on your computer and follow the steps below:
Wait till the process ends. Based on the type of error Windows will either fix it or show that it couldn’t be repaired. If Startup repair doesn’t solve the problem, try to rebuild BCD.
Detach External DrivesAdding any peripheral storage device to the PC extends its storage. The computer tries to recognize such storage as a separate disk partition. And if you attach any corrupted drives before booting, Windows tend to troubleshoot it. And if it cannot resolve issues, you will receive this type of error message.
The possible solution for this is to detach any external drives from your computer. Turn your computer off to remove and then boot your PC to check if it solves the problem.
Run CHKDSK CommandCHKDSK (Check Disk) is a Windows in-built command to troubleshoot problems related to disk. You can run this command in safe mode to fix any bad sectors existing in your disk. After you enter the Windows Recovery Environment,
You can also run this command by loading up safe mode on your Windows. Most drivers and other files that can cause problems with Windows won’t load. But you will be able to perform default windows functions, like running commands.
Reset and Reinstall WindowsSince this error may be a consequence of crashed Windows you can reset as a viable option.
To do so, you need to enter the Windows Recovery Environment first.
Then follow these steps:
But if resetting isn’t fixing the issue you can also perform a clean install of Windows.
Check the Hard Drive FaultsHard drives are physical devices which may suffer technical errors. The PC will show such an error message if your hard drive is having a hard time.
You can check the health of your disk to find its condition. Many third-party apps provide you with the features to scan and measure detailed performance of the disk. Certain PC brands like HP and Dell also provide their own software to scan and fix repairable problems.
If this error persists, high chances are that your hard drive is damaged. It can be anything ranging from motor failure in HDDs to corrupted sectors in SSDs. You can check if they have faults by using an external SATA to USB drive enclosure. Search online for such cases.
Now turn off your computer and safely remove the hard disk. Insert your hard disk in the case as per instruction manuals and connect it to any other PC. If it’s causing problems for another computer too, then you have a faulty drive.
But after checking, if you find an irreparable problem with your hard disk, move forward to repair or replace it. I would recommend consulting a technician.
Windows 11/10 Stuck On Please Wait Screen
If you start your Windows computer and it gets stuck on the “Please wait,” screen then here is how you can resolve the issue. After the computer starts, many system services start even before you log in to the computer. Services related to Network, User Interface, and more have to be ready by the time you reach your desktop.
How do you get past Windows stuck on Please wait screen?If you find that your computer screen is stuck on the Please wait screen, then here are some steps that will help you. On this screen, you will not be able to use ALT+CTRL+DEL, and so the only option you have is to remove peripheral devices, reboot the computer and follow these suggestions.
Force Automatic Startup Repair
Disable some Windows Services
Rollback Changes or perform System Restore.
1] Force Automatic Startup RepairIt would have been wise to use a Windows Bootable USB drive to boot into the safe mode, but assuming you don’t have access to any other computer, let’s force this.
First, disconnect external drives, peripherals, etc, wait for a minute and power on your system.
Now, force shutdown- and then power on – your computer three times in a row. You can do this by first turning on the computer and then immediately pressing the power button again, but this time, keep it pressed. It will turn off the computer. If you are using a desktop, you can also switch off from the power supply. Repeat this three times.
The next time you start the computer, it will begin the Automatic Startup Repair process, which will eventually launch the Advanced Recovery mode.
Go to Troubleshoot and then select Safe Mode.
2] Disable ServicesOnce the computer boots into Safe mode, you need to disable three services—
Windows Error Reporting Service,
Network List Service
Network Location Awareness.
To do this, open the Run prompt and type chúng tôi and then press the Enter key.
It will open the Windows Services Manager.
Locate the services we mentioned, and follow the steps for each of the services.
Stop it if the service is running
Change its Startup type to Disabled
Restart the computer.
3] Rollback Changes or perform System RestoreWhen you are back to the regular boot, the, Please wait screen should not hold for long, and you should get the log-in screen or the desktop if there is no password set.
While I wanted to suggest this earlier, now that you are here, you need to find the reason. If there was a change you made to the computer before the issue occurred, you might need to reverse it. If you can figure it out, it will be easy to fix the cause. If not, the best option is to restore your computer to its previous working state.
TIP: There are more suggestions here that will help you if your Windows is stuck on loading some screen.
Why does my Laptop keep saying please wait?If your laptop keeps saying Please wait – then the stuck screen can come due to corrupt Windows files. Windows files may get damaged due to viruses or any unwanted programs.
I hope this post was easy to understand and that you could pass the Windows 11/10 stuck on Please wait screen.
How To Fix Hard Disk 1 Quick 303 And Full 305 Errors
Hard disk errors 303 and full 305 are diagnostic error codes. They are the specific error messages that indicate the hard drive has failed, or is dead, and needs to be replaced immediately. A lot of times, computer users come across these errors and do not know to go about them. This post offers the most suitable solutions you can try to successfully resolve the issue.
Hard Disk 1 Quick 303 and Full 305 ErrorsThere are a few ways you can fix the Hard drive issues. We believe that the options below will be enough to solve your problem. So be sure to read carefully and follow the instructions below.
Prepare a Recovery Disk.
Backup Data from the Failing Hard Disk.
Recover Data from the Recovery Disk.
Contact HP Support for further assistance.
Let us look into this from a more detailed perspective.
1] Prepare a Recovery Drive
To create a recovery drive in windows, go to the search box next to the Start button, search for Create a recovery drive and then select it. You might be asked to enter an admin password or confirm your choice.
When the tool opens, make sure the Backup system files to the recovery drive is selected and tap Next.
Select Create. Many files need to be copied to the recovery drive, so this might take a while.
NOTE: Use an empty USB drive because this process will erase any data that are already stored on the drive. You’ll need a USB drive that’s at least 16 gigabytes.
2] Backup Data from Failing Hard Disk
The system can hardly boot when the hard drive fails with the Hard disk 1 quick 303 or Full 305 errors. The question now is, how can you backup data that is on the damaged hard drive? Here is how you go about it.
If you have done this and you’re missing an important file or folder that you have backed up, here’s how to get it back –
In the search box on the taskbar, type restore files and then select Restore your files with File History.
Look for the file you need, then use the arrows to see all its versions.
3] Recover Data from the Recovery Disk
To recover your data from an external disk through the command prompt, use the attrib command.
It supports devices like Windows drive, external HDD, USB, SD card, and any other external storage media.
Note: Remain careful when you follow the command line about to be explained. A tiny wrong typing error can result in serious problems.
Here is a Step-by-Step Guide to Recover Files from an External Drive using CMD.
Plug an external storage media into your system.
Head over to the Start menu, key in cmd in the search bar, and hit the Enter key. This will open a pane on the left, showing the command prompt.
In the CMD command line, key in the following command:
attrib -h -r -s /s /d drive letter:*.*"For instance, use
attrib -h -r -s /s /d H:*.*"If the drive you wish to recover is H. Replace H with the external drive letter of your external storage media.
You can also decide to use this alternative method:
Press Windows +R keys simultaneously, and key-in cmd in the search box.
In the command line, key in
chkdsk G/fWhere G is the disk letter you desire to recover.
Press Y until the command line starts again.
Once again, enter the drive letter, in this case, G, and hit the Enter key. The command line will go back to start.
Enter the following command:
Replace G with your disk letter and the command will retrieve all files in the drive.
After completion of the recovery process, you can create a new folder on the external drive with all recovered files.
The files might come in .chk format. Change the file extension and choose a preferred extension for each file.
Some of you may not want to go through this process when given the hard disk 1 quick 303 and full 305 errors. In that case, a piece of professional and reliable data recovery software will be helpful.
You may also want to look at how to Recover Data from a damaged Hard Drive for more details.
4] Contact HP Support for Further AssistanceIn a case where your computer is covered under warranty, you can contact HP support for further assistance and in a scenario where you don’t have a warranty, you can receive 24/7 online support. Just call 800-474-6836 for your HP product questions and 800-652-6672 for your Compaq product questions and an HP representative will explain your out-of-warranty service options.
Finally, whenever Windows is giving you the Hard disk 1 quick 303 or full 305 errors, try to repair it by following the fixes that have been stated in this post.
How To Fix Windows 10 Stuck On Just A Moment Loop
Is your PC stuck on Just a moment loop? Your Windows may have failed to install one or more updates properly and caused a system failure. Or a software you installed may have corrupted the system files. Or something may have corrupted your boot partition.
The simplest solution that you can do is to perform a restart of your PC. Windows should try to reload the required updates again. Hopefully, this should prevent the loop screen from appearing. But if it doesn’t work, you may have a real problem here.
Below, I have compiled a few approaches to help resolve the issue. I have arranged the methods in the order of severity of the issue. Make sure you start working from the first approach. Continue working your way down until the endless Windows 10 blue screen goes away.
Before diving into the actual steps, it is important to learn how to boot your Windows 10 into safe mode. Safe mode is a feature of Windows that boots Windows with the least number of required files. This means disabling any additional drivers, startup software, anti-virus programs, etc.
Safe Mode also restricts the use of certain applications so you cannot use it the same way as normal mode. It is merely for troubleshooting purposes. Once you are done using Safe Mode, you can just restart the computer and it will boot back to normal mode.
Use the following steps to log into Windows with safe mode enabled.
Start Windows in Safe Mode.
Press Win key + R to open the Run window.
Type sysdm.cpl and press OK to bring up a new window.
Go to the Advanced tab.
Under Start-up and Recovery, select Settings.
Uncheck the Automatically restart option.
Check the Write an event to the system log option.
Press OK.
Select Apply and OK to close the window.
Restart PC into normal mode.
Power off Windows by pressing the power button for 10 seconds.
Power it back on.
When the logo appears, hold the power button for another 10 seconds to power it off.
Repeat Steps 1-3 several times. You should see the Preparing Automatic Repair message on the Windows logo screen.
Under the Automatic Repair screen, select Advanced options.
Select Startup Settings.
Select Restart.
When Windows restarts, try with one of the following options disabled.
Driver signature enforcement by pressing 7 or F7
Early-launch anti-malware protection by pressing 8 or F8
Automatic restart on system failure by pressing 9 or F9
Continue on the boot process to see if you can get past the Please wait screen.
If unsuccessful, repeat the steps and try disabling the next option.
Repeat until you identify what caused the issue.
Power off Windows by pressing the power button for 10 seconds.
Power it back on.
When the logo appears, hold the power button for another 10 seconds to power it off.
Repeat Steps 1-3 several times. You should see the Preparing Automatic Repair message on the Windows logo screen.
Under the Automatic Repair screen, select Advanced options.
Select System Restore.
Select a restore point that you would like to restore to. All files and data that were created or modified past this restore point will be deleted. This will include apps as well as data.
How To Take Better Quality Screenshots On Windows 10. (Higher
Learn how to improve the quality of screenshots captured on Windows 10 PCs. An easy to enable and use option that will improve the quality of screenshots captured on your Windows 10 computer.
How to Fix Netflix Not Responding or Won’t Load Content. (Chrome, Firefox, Edge, and Other Browsers)
Taking screenshots on Windows 10 is one of the operating systems most simple tasks and is as easy as pressing the Print Screen (Prt Scr) key on your keyboard and pasting the contents to your desired location. It’s almost easier than on mobile devices. The only problem with screenshots on Windows 10 is that they are often of low quality and don’t allow you to zoom in with as much detail as screenshots taken on other devices.
Although this has been the case for quite a long time, there is also a solution that has been around for just as long, hiding in almost plain sight. With a simple flip of a toggle, you can improve the quality of screenshots captured on Windows 10 quite drastically.
Related: How to Fix the Clock on Windows 10 Not Automatically Adjusting For Time Changes. (Daylight Savings)
How Do You Make Windows 10 Take Higher Resolution Screenshots?Finally, flip the toggle next to Let Windows try to fix apps so they are not blurry to On. Alternatively, you can try to manually choose a setting that works well for you by using the Custom Scaling option. Just keep in mind that using the manual option may take a fair amount of trial and error to get ideal settings.
After making this change, you should see a decent improvement in the quality of your screenshots, however, they will still reflect the overall screen resolution of your PC. If your screen resolution is set to 1920×1080 don’t expect a screenshot to come out at 3840 x 2160…
How Do you Improve Windows 10 Screenshots Using Software?On a side note, if you have recently updated to Windows 10 version 1809, there’s a good chance you are now seeing suggestions within the Settings App. If these bother you, check out the article below which will show you how to disable them. How to Remove/Hide Suggestions From Settings on Windows 10.
Update the detailed information about Windows Is Stuck On Repairing Disk Errors, This Might Take An Hour To Complete on the Cattuongwedding.com website. We hope the article's content will meet your needs, and we will regularly update the information to provide you with the fastest and most accurate information. Have a great day!